JLCTRequest a quoteQuote

Cooling Tower Parts: Fill, Drift Eliminators and Spray Nozzles

Jinling manufactures JLCT cooling towers and supplies replacement cooling tower parts — PVC and PP film fill sheets, wave PVC drift eliminators and ABS/PP spray nozzles — for towers already in service. Requests are quoted on part, quantity and tower model or dimensions.

Request a parts quotation

Stacks of corrugated fill packs in workshop

Replacement Cooling Tower Parts: How to Order

JLCT traces its origins to 1983 in Zhuji City, Zhejiang Province, and Jinling has spent more than 40 years building cooling towers and refrigeration equipment. Fill has its own section below, drift eliminators the next, and spray nozzles the one after.

Every request is quoted on the part, the quantity and the tower model or dimensions, because sheets, blade packs and nozzles are matched to the tower they serve. Prices are given through the inquiry form on the contact page. Payment by L/C or T/T and the lead time for the order are confirmed in the quotation.

Cooling tower parts and specifications

spray nozzle (SPRAYING NOZZLE)
ParameterValue
Model NO.Spraying Nozzle
MaterialABS/PP
cooling tower fill (PVC FILL)
ParameterValue
Model NO.PVC Fill
MaterialPVC
ColourBlack
TypeIntegrated
PVC drift eliminator (PVC DRIFT ELIMINATOR)
ParameterValue
Model NO.PVC Drift Eliminator

Drift Eliminators

A drift eliminator sits above the fill and turns the leaving air through a change of direction, so water droplets carried with it strike the blade surface and drain back into the tower. Drift loss falls and less water leaves with the exhaust air.

To get a quotation, give the part, the quantity and the tower model or dimensions. Knowing whether the tower is crossflow or counterflow, and the height and depth of the eliminator section, lets the blade pack be matched to the casing; the crossflow versus counterflow guide sets out the airflow difference. Prices are given through the inquiry form.

Cooling Tower Fill

Fill is the heat-exchange media that water passes over inside a cooling tower. Film fill spreads the falling water into a thin film over a large sheet surface, so the air moving through the pack meets more water at closer spacing and heat exchange improves. PVC fill is that media in rigid sheet form, hung in packs inside the tower. When old fill clogs with scale, mud or biological growth, water channels through it and heat exchange drops.

The PVC film fill sheets are supplied as replacement parts and can be ordered as sheets to re-pack an existing tower. Fit is checked against the tower model or against measured dimensions taken from the tower itself. Buyers often write ‘filler’ for this material; it is the same thing.

The condition of the fills matters over a service life. A clean sheet pack passes air and water evenly, while a scaled, sagging or crushed pack cuts airflow, channels water and pushes the leaving water temperature closer to the wet-bulb temperature. To price a replacement, send the part, the quantity and the tower model or dimensions through the inquiry form.

Cooling Tower Components and How They Work Together

In a tower, the components work as a chain. Spray nozzles spread the hot water evenly across the top of the fill, the fill gives that water surface and time against the air, and the drift eliminator catches the droplets the air tries to carry out. A nozzle pattern that is blocked or worn starves part of the fill, and damaged fill overloads the eliminator. Each part affects the next, so they are usually reviewed together when a tower is refurbished.

The replacement components covered on this page each have their own section and the same quote call to action: send the part, the quantity and the tower model or dimensions. JLCT builds the JNT cross-flow open tower, the JFT counter-flow open tower, the JNC and JFC closed circuit towers and the JBN large industrial tower. The JNT series is listed with CTI certification code C28A-05R08; more certificates sit on the certifications page.

Spray Nozzles

Spray nozzles sit at the top of the tower and break the hot water into droplets so it lands evenly over the fill. A nozzle that is blocked, worn or missing leaves a dry patch of fill beneath it, and air takes the easiest path through the wet areas instead. ABS and PP spray nozzles are supplied as replacement parts, and the specification tables on this page give their models and materials.

A request for spray nozzles is quoted on the part, the quantity and the tower model or dimensions. Nozzle spacing and flow follow the tower design, so the model or a measured layout is where matching starts. Prices are given through the inquiry form.

Request a quotation

Send the part, quantity, tower model and any measurements or photos you have.

Or write to sales@coolingtowerfactory.com

* Required